Iomega iconnect software windows 10. Iomega Drivers

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Instalation is simple, just connect JTAG to usb wait till system inform you that cannot find a drivers, then install it manually by device. The Iomega iConnect Wireless Data Station is a great device to quickly Manager software, you can also access the iConnect using Windows.
 
 

 

[OpenWrt Wiki] Iomega iConnect

 

Picture 1. First pin is in white rectangle, just next to connector name J2. This may be important when you connect USB storage. If many devices are connected at once then they will be mounted according to numeration of port. This tutorial assumes that you are using Windows 7 OS. Using description above connect serial cable to board and establish connection with serial console using PuTTY. Download from trunk repository or final version if available:. This is risky operation which can brick your iConnect.

Please first skip to next point and continue with you current U-Boot. If you will be having problems with running OpenWrt then come back here. If your iConnect does not bring up blue diode don’t blink , something went wrong and it is bricked.

To prevent any problems caused by old environment configuration it is best to reset them to default values. To force U-Boot to recreate whole env with basic configuration you may erase this part of flash memory.

It can be risky if env storage location is changed with future version and you erase part of U-Boot. To fix it you must restore MAC address search for ethaddr in your backup file and save env values:.

Please refer to section 6. It’s important that you reset u-boot before flashing otherwise it will most likely fail to boot. By default in OpenWrt network address is set to static We can change it. If you want to use DHCP in local network set it to:.

More about network configuration: Network Wiki. It is based on my own experience as I broke U-Boot by improper flashing using serial cable and tftp server. For FTDI chips there are at least four drivers avaliable. Instalation is simple, just connect JTAG to usb wait till system inform you that cannot find a drivers, then install it manually by device manager providing a patch to WinUSB drivers. In case that you have a problems with installing drivers or want to replace it use Zadig.

Get latest stable version from www. Unzip it to C: and open openocd Download board configuration files for OpenOCD: – copy iconnect. You may use PuTTY for that. Configure as follow:. You may want to save configuration for future usage. Download U-Boot image openwrt-kirkwood-iconnect-u-boot. This is alternative to direct flashing which is not working in my case. After reset the blue LED should start blinking and on serial console you will see U-Boot boot messages. How to add tags.

Show pagesource Old revisions Backlinks Back to top. Connect Serial Cable 2. Connecting LAN 3. Tftp server configuration 4. Updating U-Boot 5. Default U-Boot configuration 6.

Flash OpenWrt with fresh U-Boot 7. Accessing iConnect with SSH 8. Setting up Internet access 9. Introduction 2. Hardware and software used 3. Configuration 6. Connecting with OpenOCD to board 7. Connect to OpenOCD telnet interface. First method – direct flash U-Boot 9. Post rescue procedure. Iomega iConnect.

Connect LAN cable between your computer and iConnect. Set computer IP to Download from trunk repository or final version if available: openwrt-kirkwood-uImage openwrt-kirkwood–jffsk.

Even when you brick it, you may use JTAG connector to bring it live. Power up iConnect and watch serial console output. When you notice: Hit any key to stop autoboot: 0 press enter. Then type: printenv you will see all env variables, copy it and save to text file it will be needed later. Set tftp server and iConnect IP addresses.

Here is a default configuration of first run U-Boot. Find in your backup file MAC address, variable ethaddr. This is a bootlog from first start of OpenWrt: U-Boot Image Name: Linux OK Loading Kernel Image Uncompressing Linux OK Starting kernel Total pages: [ 0.

To activate SSH you must first login with telnet. If you want to use DHCP in local network set it to: config interface ‘lan’ option ifname ‘eth0’ option proto ‘dhcp’ If you want to use Internet connection from your provider change it to: config interface ‘wan’ option ifname ‘eth0’ option proto ‘dhcp’ option macaddr ‘ : : : ‘ Optional WAN or LAN names make different from firewall point of view.

Save it and reset iConnect. To install the RT driver you need to install the kmod-rtpci package: opkg update opkg install kmod-rtpci opkg install iw Then you should see the options to enable the wireless adapter in luci.

Run: openocd-x Configure as follow: Host Name: I keep getting error: nand write 0 openwrt-kirkwood-iconnect-u-boot. Copy downloaded openwrt-kirkwood-iconnect-u-boot.

Check if Server interface is Establish Connection with board as described in point 6 and 7. Using PuTTY connect to your serial cable, put window in visible area and monitor it. We need to set server address and iConnect address to establish communication. In Serial console execute: setenv ethaddr ‘D’ setenv serverip That’s all your iConnect is unbricked.

You should set basic env settings by executing: setenv ethaddr ‘D0: : : : ‘ Put here your real MAC address setenv serverip This website uses cookies.

By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website. OK More information about cookies. Product Brief Technical Product Brief. Datasheet Drivers.